Français

e-Laws

O. Reg. 297/17: GENERAL - WASTE MANAGEMENT, Filed July 28, 2017 under Environmental Protection Act, R.S.O. 1990, c. E.19

 

ontario regulation 297/17

made under the

Environmental Protection Act

Made: July 26, 2017
Filed: July 28, 2017
Published on e-Laws: July 31, 2017
Printed in The Ontario Gazette: August 12, 2017

Amending Reg. 347 of R.R.O. 1990

(GENERAL - WASTE MANAGEMENT)

1. Subsections 75 (4), 76 (4), 77 (4) and 79 (7) of Regulation 347 of the Revised Regulations of Ontario, 1990 are revoked.

2. Schedule 1 to the Regulation 347 is amended by striking out,

 

F005

The following spent non-halogenated solvents: Toluene, methyl ethyl ketone, carbon disulfide, isobutanol, pyridine, benzene, 2-ethoxyethanol, and 2-nitropropane; all spent solvent mixtures/blends containing, before use, a total of ten per cent or more (by volume) of one or more of the above non-halogenated solvents or those solvents listed in F001, F002 or F004; and still bottoms from the recovery of these spent solvents and spent solvent mixtures.

Treatment Subcategory 1

All F003 wastes, except those identified in Subcategory 2:

same as F001

 

 

 

Treatment Subcategory 2

F003 solvent wastes, that contain any combination of one or more of the following three solvents as the only listed F001-5 solvents: carbon disulfide, cyclohexanone and/or methanol:

same as F003 Subcategory 2

 

 

 

Treatment Subcategory 3

F005 solvent waste containing 2-Nitropropane as the only listed F001-5 solvents:

2-Nitropropane

79-46-9

(WETOX or CHOXD)
fb CARBN; or CMBST

CMBST

Treatment Subcategory 4

F005 solvent waste containing 2-Ethoxyethanol as the only listed F001-5 solvents:

2-Ethoxyethanol

110-80-5

BIODG; or CMBST

CMBST

 

and substituting:

 

F005

The following spent non-halogenated solvents: Toluene, methyl ethyl ketone, carbon disulfide, isobutanol, pyridine, benzene, 2-ethoxyethanol, and 2-nitropropane; all spent solvent mixtures/blends containing, before use, a total of ten per cent or more (by volume) of one or more of the above non-halogenated solvents or those solvents listed in F001, F002 or F004; and still bottoms from the recovery of these spent solvents and spent solvent mixtures.

Treatment Subcategory 1

All F005 wastes, except those identified in Subcategory 2:

same as F001

 

 

 

Treatment Subcategory 2

F005 solvent wastes, that contain any combination of one or more of the following three solvents as the only listed F001-5 solvents: carbon disulfide, cyclohexanone and/or methanol:

same as F003 Subcategory 2

 

 

 

Treatment Subcategory 3

F005 solvent waste containing 2-Nitropropane as the only listed F001-5 solvents:

2-Nitropropane

79-46-9

(WETOX or CHOXD)
fb CARBN; or CMBST

CMBST

Treatment Subcategory 4

F005 solvent waste containing 2-Ethoxyethanol as the only listed F001-5 solvents:

2-Ethoxyethanol

110-80-5

BIODG; or CMBST

CMBST

 

3. (1)  Part A of Schedule 2 to the Regulation is amended by striking out,

 

P030

N/A

Cyanides (soluble cyanide salts), not otherwise specified

Cyanides (Total)7

57-12-5

1.2

590

Cyanides (Amenable)7

57-12-5

0.86

30

 

 

 

 

 

and substituting:

 

P030

NA

Cyanides (soluble cyanide salts), not otherwise specified

Cyanides (Total)7

57-12-5

1.2

590

Cyanides (Amenable)7

57-12-5

0.86

30

 

 

 

 

 

(2)  Part B of Schedule 2 to the Regulation is amended by striking out,

 

U051

N/A

Creosote

Naphthalene

91-20-3

0.059

5.6

Pentachlorophenol

87-86-5

0.089

7.4

Phenanthrene

85-01-8

0.059

5.6

Pyrene

129-00-0

0.067

8.2

Toluene

108-88-3

0.08

10

Xylenes-mixed isomers (sum of o-, m-, and p-xylene concentrations)

1330-20-7

0.32

30

Lead

7439-92-1

0.69

0.75 mg/L TCLP

 

and substituting:

 

U051

NA

Creosote

Naphthalene

91-20-3

0.059

5.6

Pentachlorophenol

87-86-5

0.089

7.4

Phenanthrene

85-01-8

0.059

5.6

Pyrene

129-00-0

0.067

8.2

Toluene

108-88-3

0.08

10

Xylenes-mixed isomers (sum of o-, m-, and p-xylene concentrations)

1330-20-7

0.32

30

Lead

7439-92-1

0.69

0.75 mg/L TCLP

 

4. Schedule 2.1 to the Regulation is amended by striking out the Table and substituting the following:

There are no wastes currently listed in this Schedule.

5. Schedule 2.2 to the Regulation is amended by striking out the Table and substituting the following:

There are no wastes currently listed in this Schedule.

6. Schedule 3 to the Regulation is revoked and the following substituted:

Schedule 3
Severely Toxic Contaminants

This Schedule consists of a Table and Notes.

Table

 

Column 1

Severely Toxic Contaminant:

Hazardous Waste Number

Column 2

Severely Toxic Contaminant:

CAS Number

Column 3

Severely Toxic Contaminant

Column 4

Regulated Constituent:

Generic Name or other description

Column 5

Regulated Constituent:

CAS Number

Column 6

Land Disposal Treatment Requirements for Aqueous Waste:

Concentration (mg/L)

Column 7

Land Disposal Treatment Requirements for Non-aqueous Waste:

Concentration (mg/kg)

S001

1402-68-2

Aflatoxin

Aflatoxin

1402-68-2

NA

NA

S002

1746-01-6

2,3,7,8-Tetrachlorodibenzo-p-dioxin

TCDDs (All Tetrachlorodibenzo-p-dioxins)

41903-57-5

0.000063

0.001

S003

40321-76-4

1,2,3,7,8-Pentachlorodibenzo-p-dioxin

PeCDDs (All Pentachlorodibenzo-p-dioxins)

36088-22-9

0.000063

0.001

S004

39227-28-6

1,2,3,4,7,8-Hexachlorodibenzo-p-dioxin

HxCDDs (All Hexachlorodibenzo-p-dioxins)

34465-46-8

0.000063

0.001

S005

57653-85-7

1,2,3,6,7,8-Hexachlorodibenzo-p-dioxin

HxCDDs (All Hexachlorodibenzo-p-dioxins)

34465-46-8

0.000063

0.001

S006

19408-74-3

1,2,3,7,8,9-Hexachlorodibenzo-p-dioxin

HxCDDs (All Hexachlorodibenzo-p-dioxins)

34465-46-8

0.000063

0.001

S007

51207-31-9

2,3,7,8-Tetrachlorodibenzo furan

TCDFs (All Tetrachlorodibenzofurans)

55722-27-5

0.000063

0.001

Notes to Schedule 3:

1. The Hazardous Waste Numbers are consistent with United States Environmental Protection Agency Hazardous Waste Numbers.  If there is no United States Environmental Protection Agency Hazardous Waste Number for a waste, the Hazardous Waste Number is assigned to the waste by the Ontario Ministry of the Environment.

2. CAS Number means the Chemical Abstracts Service Registry Number.  When the waste or a regulated constituent is described as a combination of a chemical with its salts or esters, the CAS number is given for the parent compound only.

3. Concentration requirements for aqueous wastes are based on analysis of composite samples.

4. Concentration requirements for non-aqueous wastes are based on analysis of grab samples.

7. Schedule 4 to the Regulation is revoked and the following substituted:

Schedule 4
Leachate Quality Criteria

This Schedule consists of a Table and Notes.

Table

 

Contaminant

CAS Number

Hazardous Waste Number

Concentration (mg/L TCLP)

Aldicarb

116-06-3

E101

0.9

Aldrin + Dieldrin

309-00-2, 60-57-1

E001

0.07

Arsenic

7440-38-2

D004

2.5

Atrazine + N-dealkylated metabolites (Weedex)

1912-24-9

E102

0.5

Azinphos-methyl

86-50-0

E103

2

Barium

7440-39-3

D005

100

Bendiocarb

22781-23-3

E002

4

Benzene

71-43-2

D018

0.5

Benzo(a)pyrene

50-32-8

E003

0.001

Boron

7440-42-8

E104

500

Bromoxynil

1689-84-5

E105

0.5

Cadmium

7440-43-9

D006

0.5

Carbaryl/Sevin/1-Naphthyl-N methyl carbamate

63-25-2

E004

9

Carbofuran

1563-66-2

E005

9

Carbon tetrachloride (Tetrachloromethane)

56-23-5

D019

0.5

Chlordane

57-74-9

D020

0.7

Chlorobenzene (Monochlorobenzene)

108-90-7

D021

8

Chloroform

67-66-3

D022

10

Chlorpyrifos

2921-88-2

E106

9

Chromium

7440-47-3

D007

5

Cresol (Mixture - total of all isomers, when isomers cannot be differentiated)

NA

D026

200

m-Cresol

108-39-4

D024

200

o-Cresol

95-48-7

D023

200

p-Cresol

106-44-5

D025

200

Cyanazine

21725-46-2

E107

1

Cyanide

NA

E006

20

2,4-D / (2,4-dichlorophenoxy)acetic acid

94-75-7

D016

10

2,4-DCP (2,4-Dichlorophenol)

120-83-2

E007

90

DDT (total isomers)

NA

E008

3

Diazinon/Phosphordithioic acid, o,o-diethyl o-(2-isopropyl 6-methyl-4-pyrimidinyl) ester

333-41-5

E108

2

Dicamba

1918-00-9

E109

12

1,2-Dichlorobenzene (o-Dichlorobenzene)

95-50-1

E009

20

1,4-Dichlorobenzene (p-Dichlorobenzene)

106-46-7

D027

0.5

1,2-Dichloroethane (Ethylene dichloride)

107-06-2

D028

0.5

1,1-Dichloroethylene (Vinylidene chloride)

75-35-4

D029

1.4

Dichloromethane (also see - methylene chloride)

75-09-02

E010

5

Diclofop-methyl

51338-27-3

E110

0.9

Dimethoate

60-51-5

E111

2

2,4-Dinitrotoluene

121-14-2

D030

0.13

Dinoseb

88-85-7

E012

1

Dioxin & Furan

NA

E013

0.0000015 Toxic Equivalent (TEQ)

Diquat

231-36-7

E112

7

Diuron

330-54-1

E113

15

Endrin

72-20-8

D012

0.02

Fluoride

NA

E014

150

Glyphosate

1071-83-6

E114

28

Heptachlor + Heptachlor epoxide

76-44-8, 1024-57-3

D031

0.3

Hexachlorobenzene

118-74-1

D032

0.13

Hexachlorobutadiene

87-68-3

D033

0.5

Hexachloroethane

67-72-1

D034

3

Lead

7439-92-1

D008

5

Lindane

58-89-9

D013

0.4

Malathion

121-75-5

E115

19

Mercury

7439-97-6

D009

0.1

Methoxychlor/1,1,1-Trichloro-2,2-bis(p-methoxyphenyl) ethane

72-43-5

D014

90

Methyl ethyl ketone / Ethyl methyl ketone

78-93-3

D035

200

Methyl Parathion

298-00-0

E015

0.7

Methylene chloride / Dichloromethane

75-09-02

E011

5

Metolachlor

51218-45-2

E116

5

Metribuzin

21087-64-9

E117

8

NDMA

62-75-9

E016

0.0009

Nitrate + Nitrite (as Nitrogen)

NA

E118

1000

Nitrilotriacetic acid (NTA)

139-13-9

E119

40

Nitrobenzene

98-95-3

D036

2

Paraquat

4685-14-7

E120

1

Parathion

56-38-2

E017

5

PCBs

NA

E018

0.3

Pentachlorophenol

87-86-5

D037

6

Phorate

298-02-2

E019

0.2

Picloram

1918-02-1

E121

19

Pyridine

110-86-1

D038

5

Selenium

7782-49-2

D010

1

Silver

7440-22-4

D011

5

Simazine

122-34-9

E122

1

2,4,5-T (2,4,5-Trichlorophenoxyacetic acid)

93-76-5

E020

28

2,4,5-TP/ Silvex/ 2-(2,4,5-Trichlorophenoxy)propionic acid

93-72-1

D017

1

Temephos

3383-96-8

E123

28

Terbufos

13071-79-9

E124

0.1

Tetrachloroethylene

127-18-4

D039

3

2,3,4,6-Tetrachlorophenol /(2,3,4,6-TeCP)

58-90-2

E021

10

Toxaphene

8001-35-2

D015

0.5

Triallate

2303-17-5

E022

23

Trichloroethylene

79-01-6

D040

5

2,4,5-Trichlorophenol (2,4,5-TCP)

95-95-4

D041

400

2,4,6-Trichlorophenol (2,4,6-TCP)

88-06-2

D042

0.5

Trifluralin

1582-09-8

E125

4.5

Uranium

7440-61-1

E126

10

Vinyl chloride

75-01-4

D043

0.2

Notes to Schedule 4:

1. CAS Number means the Chemical Abstracts Service Registry Number. When the waste or a regulated constituent is described as a combination of a chemical with its salts or esters, the CAS number is given for the parent compound only.

2. Hazardous Waste Numbers are consistent with United States Environmental Protection Agency Hazardous Waste Numbers.  If there is no United States Environmental Protection Agency Hazardous Waste Number for a waste, the Hazardous Waste Number is assigned to the waste by the Ontario Ministry of the Environment.

8. Schedule 5 to the Regulation is amended by striking out,

 

E002

Wastes that are leachate toxic for Bendiocarb based on the Toxicity Characteristic Leaching Procedure.

Bendiocarb

22781-23-3

N/A

1.4 and meet Schedule 6 standards

E003

Wastes that are leachate toxic for Benzo(a)pyrene based on the Toxicity Characteristic Leaching Procedure.

Benzo(a)pyrene

50-32-8

N/A

3.4 and meet Schedule 6 standards

E004

Wastes that are leachate toxic for Carbaryl/Sevin/1-Naphthyl-N methyl carbamate based on the Toxicity Characteristic Leaching Procedure.

Carbaryl/Sevin/1-Naphthyl-N methyl carbamate

63-25-2

N/A

0.14 and meet Schedule 6 standards

E005

Wastes that are leachate toxic for Carbofuran based on the Toxicity Characteristic Leaching Procedure.

Carbofuran

1563-66-2

N/A

0.14 and meet Schedule 6 standards

E006

Wastes that exhibit, or are expected to exhibit, the characteristic of toxicity for Cyanide based on the Toxicity Characteristic Leaching Procedure.

Cyanides (Total)7

57-12-5

1.2 and meet Schedule 6 standards

590 and meet Schedule 6 standards

Cyanides (Amenable)7

57-12-5

0.86 and meet Schedule 6 standards

30 and meet Schedule 6 standards

E007

Wastes that are leachate toxic for 2,4-DCP (2,4-Dichlorophenol) based on the Toxicity Characteristic Leaching Procedure.

2,4-DCP (2,4-Dichlorophenol)

120-83-2

N/A

14 and meet Schedule 6 standards

E008

Wastes that are leachate toxic for DDT (total isomers) based on the Toxicity Characteristic Leaching Procedure.

DDT (total isomers)

 

N/A

0.087 and meet Schedule 6 standards

E009

Wastes that are leachate toxic for 1,2-Dichlorobenzene (o-Dichlorobenzene) based on the Toxicity Characteristic Leaching Procedure.

1,2-Dichlorobenzene (o-Dichlorobenzene)

95-50-1

N/A

6.0 and meet Schedule 6 standards

E010

Wastes that are leachate toxic for Dichloromethane (also see - methylene chloride) based on the Toxicity Characteristic Leaching Procedure.

Dichloromethane (also see - methylene chloride)

75-09-02

N/A

30 and meet Schedule 6 standards

E011

Wastes that are leachate toxic for Methylene chloride / Dichloromethane based on the Toxicity Characteristic Leaching Procedure.

Methylene chloride / Dichloromethane

75-09-02

N/A

30 and meet Schedule 6 standards

E012

Wastes that are leachate toxic for Dinoseb based on the Toxicity Characteristic Leaching Procedure.

Dinoseb

88-85-7

N/A

2.5 and meet Schedule 6 standards

E013

Wastes that are leachate toxic for Dioxin & Furans based on the Toxicity Characteristic Leaching Procedure.

1,2,3,4,6,7,8-Heptachlorodibenzo-p-dioxin, (1,2,3,4,6,7,8-HpCDD)

35822-46-9

0.000035 and meet Schedule 6 standards

0.0025 and meet Schedule 6 standards

1,2,3,4,6,7,8-Heptachlorodibenzofuran, (1,2,3,4,6,7,8-HpCDF)

67562-39-4

0.000035 and meet Schedule 6 standards

0.0025 and meet Schedule 6 standards

1,2,3,4,7,8,9-Heptachlorodibenzofuran, (1,2,3,4,7,8,9-HpCDF)

55673-89-7

0.000035 and meet Schedule 6 standards

0.0025 and meet Schedule 6 standards

HxCDDs (All Hexachlorodibenzo-p-dioxins)

34465-46-8

0.000063 and meet Schedule 6 standards

0.001 and meet Schedule 6 standards

HxCDFs (All Hexachlorodibenzofurans)

55684-94-1

0.000063 and meet Schedule 6 standards

0.001 and meet Schedule 6 standards

1,2,3,4,6,7,8,9-Octachlorodibenzo-p-dioxin, (OCDD)

3268-87-9

0.000063 and meet Schedule 6 standards

0.001 and meet Schedule 6 standards

1,2,3,4,6,7,8,9-Octachlorodibenzofuran, (OCDF)

39001-02-0

0.000063 and meet Schedule 6 standards

0.001 and meet Schedule 6 standards

PeCDDs (All Pentachlorodibenzo-p-dioxins

36088-22-9

0.000063 and meet Schedule 6 standards

0.001 and meet Schedule 6 standards

PeCDFs (All Pentachlorodibenzofurans)

30402-15-4

0.000035 and meet Schedule 6 standards

0.001 and meet Schedule 6 standards

TCDDs (All tetachlorodibenzo-p-dioxins)

41903-57-5

0.000063 and meet Schedule 6 standards

0.001 and meet Schedule 6 standards

TCDFs (All tetrachlorodibenzofurans)

55722-27-5

0.000063 and meet Schedule 6 standards

0.001 and meet Schedule 6 standards

E014

Wastes that exhibit, or are expected to exhibit, the characteristic of toxicity for Fluoride based on the Toxicity Characteristic Leaching Procedure.

Fluoride

16984-48-8

35 and meet Schedule 6 standards

NA

E015

Wastes that are leachate toxic for Methyl Parathion based on the Toxicity Characteristic Leaching Procedure.

Methyl Parathion

298-00-0

N/A

4.6 and meet Schedule 6 standards

E016

Wastes that are leachate toxic for NDMA based on the Toxicity Characteristic Leaching Procedure.

NDMA

62-75-9

N/A

2.3 and meet Schedule 6 standards

E017

Wastes that are leachate toxic for Parathion based on the Toxicity Characteristic Leaching Procedure.

Parathion

56-38-2

N/A

4.6 and meet Schedule 6 standards

E018

Wastes that are leachate toxic for PCBs based on the Toxicity Characteristic Leaching Procedure.

Total PCBs (Sum of all PCB Isomers, or all Aroclors)

1336-36-3

0.10 and meet Schedule 6 standards

10 and meet Schedule 6 standards

E019

Wastes that are leachate toxic for Phorate based on the Toxicity Characteristic Leaching Procedure.

Phorate

298-02-2

N/A

4.6 and meet Schedule 6 standards

E020

Wastes that are leachate toxic for 2,4,5-T (2,4,5-Trichlorophenoxyacetic acid) based on the Toxicity Characteristic Leaching Procedure.

2,4,5-T (2,4,5-Trichlorophenoxyacetic acid)

93-76-5

N/A

7.9 and meet Schedule 6 standards

E021

Wastes that are leachate toxic for 2,3,4,6-Tetrachlorophenol /(2,3,4,6-TeCP) based on the Toxicity Characteristic Leaching Procedure.

2,3,4,6-Tetrachlorophenol /(2,3,4,6-TeCP)

58-90-2

N/A

7.4 and meet Schedule 6 standards

E022

Wastes that are leachate toxic for Triallate based on the Toxicity Characteristic Leaching Procedure.

Triallate

2303-17-5

N/A

1.4 and meet Schedule 6 standards

 

and substituting:

 

E002

Wastes that are leachate toxic for Bendiocarb based on the Toxicity Characteristic Leaching Procedure.

Bendiocarb

22781-23-3

NA

1.4 and meet Schedule 6 standards

E003

Wastes that are leachate toxic for Benzo(a)pyrene based on the Toxicity Characteristic Leaching Procedure.

Benzo(a)pyrene

50-32-8

NA

3.4 and meet Schedule 6 standards

E004

Wastes that are leachate toxic for Carbaryl/Sevin/1-Naphthyl-N methyl carbamate based on the Toxicity Characteristic Leaching Procedure.

Carbaryl/Sevin/1-Naphthyl-N methyl carbamate

63-25-2

NA

0.14 and meet Schedule 6 standards

E005

Wastes that are leachate toxic for Carbofuran based on the Toxicity Characteristic Leaching Procedure.

Carbofuran

1563-66-2

NA

0.14 and meet Schedule 6 standards

E006

Wastes that exhibit, or are expected to exhibit, the characteristic of toxicity for Cyanide based on the Toxicity Characteristic Leaching Procedure.

Cyanides (Total)7

57-12-5

1.2 and meet Schedule 6 standards

590 and meet Schedule 6 standards

Cyanides (Amenable)7

57-12-5

0.86 and meet Schedule 6 standards

30 and meet Schedule 6 standards

E007

Wastes that are leachate toxic for 2,4-DCP (2,4-Dichlorophenol) based on the Toxicity Characteristic Leaching Procedure.

2,4-DCP (2,4-Dichlorophenol)

120-83-2

NA

14 and meet Schedule 6 standards

E008

Wastes that are leachate toxic for DDT (total isomers) based on the Toxicity Characteristic Leaching Procedure.

DDT (total isomers)

 

NA

0.087 and meet Schedule 6 standards

E009

Wastes that are leachate toxic for 1,2-Dichlorobenzene (o-Dichlorobenzene) based on the Toxicity Characteristic Leaching Procedure.

1,2-Dichlorobenzene (o-Dichlorobenzene)

95-50-1

NA

6.0 and meet Schedule 6 standards

E010

Wastes that are leachate toxic for Dichloromethane (also see - methylene chloride) based on the Toxicity Characteristic Leaching Procedure.

Dichloromethane (also see - methylene chloride)

75-09-02

NA

30 and meet Schedule 6 standards

E011

Wastes that are leachate toxic for Methylene chloride / Dichloromethane based on the Toxicity Characteristic Leaching Procedure.

Methylene chloride / Dichloromethane

75-09-02

NA

30 and meet Schedule 6 standards

E012

Wastes that are leachate toxic for Dinoseb based on the Toxicity Characteristic Leaching Procedure.

Dinoseb

88-85-7

NA

2.5 and meet Schedule 6 standards

E013

Wastes that are leachate toxic for Dioxin & Furans based on the Toxicity Characteristic Leaching Procedure.

1,2,3,4,6,7,8-Heptachlorodibenzo-p-dioxin, (1,2,3,4,6,7,8-HpCDD)

35822-46-9

0.000035 and meet Schedule 6 standards

0.0025 and meet Schedule 6 standards

1,2,3,4,6,7,8-Heptachlorodibenzofuran, (1,2,3,4,6,7,8-HpCDF)

67562-39-4

0.000035 and meet Schedule 6 standards

0.0025 and meet Schedule 6 standards

1,2,3,4,7,8,9-Heptachlorodibenzofuran, (1,2,3,4,7,8,9-HpCDF)

55673-89-7

0.000035 and meet Schedule 6 standards

0.0025 and meet Schedule 6 standards

HxCDDs (All Hexachlorodibenzo-p-dioxins)

34465-46-8

0.000063 and meet Schedule 6 standards

0.001 and meet Schedule 6 standards

HxCDFs (All Hexachlorodibenzofurans)

55684-94-1

0.000063 and meet Schedule 6 standards

0.001 and meet Schedule 6 standards

1,2,3,4,6,7,8,9-Octachlorodibenzo-p-dioxin, (OCDD)

3268-87-9

0.000063 and meet Schedule 6 standards

0.001 and meet Schedule 6 standards

1,2,3,4,6,7,8,9-Octachlorodibenzofuran, (OCDF)

39001-02-0

0.000063 and meet Schedule 6 standards

0.001 and meet Schedule 6 standards

PeCDDs (All Pentachlorodibenzo-p-dioxins

36088-22-9

0.000063 and meet Schedule 6 standards

0.001 and meet Schedule 6 standards

PeCDFs (All Pentachlorodibenzofurans)

30402-15-4

0.000035 and meet Schedule 6 standards

0.001 and meet Schedule 6 standards

TCDDs (All tetachlorodibenzo-p-dioxins)

41903-57-5

0.000063 and meet Schedule 6 standards

0.001 and meet Schedule 6 standards

TCDFs (All tetrachlorodibenzofurans)

55722-27-5

0.000063 and meet Schedule 6 standards

0.001 and meet Schedule 6 standards

E014

Wastes that exhibit, or are expected to exhibit, the characteristic of toxicity for Fluoride based on the Toxicity Characteristic Leaching Procedure.

Fluoride

16984-48-8

35 and meet Schedule 6 standards

NA

E015

Wastes that are leachate toxic for Methyl Parathion based on the Toxicity Characteristic Leaching Procedure.

Methyl Parathion

298-00-0

NA

4.6 and meet Schedule 6 standards

E016

Wastes that are leachate toxic for NDMA based on the Toxicity Characteristic Leaching Procedure.

NDMA

62-75-9

NA

2.3 and meet Schedule 6 standards

E017

Wastes that are leachate toxic for Parathion based on the Toxicity Characteristic Leaching Procedure.

Parathion

56-38-2

NA

4.6 and meet Schedule 6 standards

E018

Wastes that are leachate toxic for PCBs based on the Toxicity Characteristic Leaching Procedure.

Total PCBs (Sum of all PCB Isomers, or all Aroclors)

1336-36-3

0.10 and meet Schedule 6 standards

10 and meet Schedule 6 standards

E019

Wastes that are leachate toxic for Phorate based on the Toxicity Characteristic Leaching Procedure.

Phorate

298-02-2

NA

4.6 and meet Schedule 6 standards

E020

Wastes that are leachate toxic for 2,4,5-T (2,4,5-Trichlorophenoxyacetic acid) based on the Toxicity Characteristic Leaching Procedure.

2,4,5-T (2,4,5-Trichlorophenoxyacetic acid)

93-76-5

NA

7.9 and meet Schedule 6 standards

E021

Wastes that are leachate toxic for 2,3,4,6-Tetrachlorophenol /(2,3,4,6-TeCP) based on the Toxicity Characteristic Leaching Procedure.

2,3,4,6-Tetrachlorophenol /(2,3,4,6-TeCP)

58-90-2

NA

7.4 and meet Schedule 6 standards

E022

Wastes that are leachate toxic for Triallate based on the Toxicity Characteristic Leaching Procedure.

Triallate

2303-17-5

NA

1.4 and meet Schedule 6 standards

 

9. Schedule 6 to the Regulation is revoked and the following substituted:

Schedule 6
Universal Treatment Standards (UTS) for Characteristic Wastes

A reference to this Schedule in this Regulation is a reference to the relevant Table of this Schedule, including the Notes to the Table.

Table 1
Organic Constituents

 

Column 1

Regulated Constituent:

Common Name

Column 2

Regulated Constituent:

CAS Number

Column 3

Land Disposal Treatment Requirements for Aqueous Waste:

Concentration (mg/L)

Column 4

Land Disposal Treatment Requirements for Non-aqueous Waste:

Concentration (mg/kg, unless otherwise indicated)

Acenaphthylene

208-96-8

0.059

3.4

Acenaphthene

83-32-9

0.059

3.4

Acetone

67-64-1

0.28

160

Acetonitrile

75-05-8

5.6

38

Acetophenone

96-86-2

0.010

9.7

2-Acetylaminofluorene

53-96-3

0.059

140

Acrolein

107-02-8

0.29

NA

Acrylamide

79-06-1

19

23

Acrylonitrile

107-13-1

0.24

84

Aldicarb sulfone

1646-88-4

0.056

0.28

Aldrin

309-00-2

0.021

0.066

4-Aminobiphenyl

92-67-1

0.13

NA

Aniline

62-53-3

0.81

14

Anthracene

120-12-7

0.059

3.4

Aramite

140-57-8

0.36

NA

alpha-BHC

319-84-6

0.00014

0.066

beta-BHC

319-85-7

0.00014

0.066

delta-BHC

319-86-8

0.023

0.066

gamma-BHC

58-89-9

0.0017

0.066

Barban

101-27-9

0.056

1.4

Bendiocarb

22781-23-3

0.056

1.4

Benomyl

17804-35-2

0.056

1.4

Benzene

71-43-2

0.14

10

Benz(a)anthracene

56-55-3

0.059

3.4

Benzal chloride

98-87-3

0.055

6.0

Benzo(b)fluoranthene (difficult to distinguish from benzo(k)fluoranthene)

205-99-2

0.11

6.8

Benzo(k)fluoranthene (difficult to distinguish from benzo(b)fluoranthene)

207-08-9

0.11

6.8

Benzo(g,h,i)perylene

191-24-2

0.0055

1.8

Benzo(a)pyrene

50-32-8

0.061

3.4

Bromodichloromethane

75-27-4

0.35

15

Bromomethane/Methyl bromide

74-83-9

0.11

15

4-Bromophenyl phenyl ether

101-55-3

0.055

15

n-Butyl alcohol

71-36-3

5.6

2.6

Butylate

2008-41-5

0.042

1.4

Butyl benzyl phthalate

85-68-7

0.017

28

2-sec-Butyl-4,6-dinitrophenol (Dinoseb)

88-85-7

0.066

2.5

Carbaryl

63-25-2

0.006

0.14

Carbendazim

10605-21-7

0.056

1.4

Carbofuran

1563-66-2

0.006

0.14

Carbofuran phenol

1563-38-8

0.056

1.4

Carbon disulfide

75-15-0

3.8

4.8 mg/L TCLP

Carbon tetrachloride

56-23-5

0.057

6.0

Carbosulfan

55285-14-8

0.028

1.4

Chlordane (alpha and gamma isomers)

57-74-9

0.0033

0.26

p-Chloroaniline

106-47-8

0.46

16

Chlorobenzene

108-90-7

0.057

6.0

Chlorobenzilate

510-15-6

0.10

NA

2-Chloro-1,3-butadiene

126-99-8

0.057

0.28

Chlorodibromomethane

124-48-1

0.057

15

Chloroethane

75-00-3

0.27

6.0

bis(2-Chloroethoxy)methane

111-91-1

0.036

7.2

bis(2-Chloroethyl)ether

111-44-4

0.033

6.0

Chloroform

67-66-3

0.046

6.0

bis(2-Chloroisopropyl)ether

39638-32-9

0.055

7.2

p-Chloro-m-cresol

59-50-7

0.018

14

2-Chloroethyl vinyl ether

110-75-8

0.062

NA

Chloromethane/Methyl chloride

74-87-3

0.19

30

2-Chloronaphthalene

91-58-7

0.055

5.6

2-Chlorophenol

95-57-8

0.044

5.7

3-Chloropropylene

107-05-1

0.036

30

Chrysene

218-01-9

0.059

3.4

o-Cresol

95-48-7

0.11

5.6

m-Cresol (difficult to distinguish from p-cresol)

108-39-4

0.77

5.6

p-Cresol (difficult to distinguish from m-cresol)

106-44-5

0.77

5.6

m-Cumenyl methylcarbamate

64-00-6

0.056

1.4

Cyclohexanone

108-94-1

0.36

0.75 mg/L TCLP

o,p'-DDD

53-19-0

0.023

0.087

p,p'-DDD

72-54-8

0.023

0.087

o,p'-DDE

3424-82-6

0.031

0.087

p,p'-DDE

72-55-9

0.031

0.087

o,p'-DDT

789-02-6

0.0039

0.087

p,p'-DDT

50-29-3

0.0039

0.087

Dibenz(a,h)anthracene

53-70-3

0.055

8.2

Dibenz(a,e)pyrene

192-65-4

0.061

NA

1,2-Dibromo-3-chloropropane

96-12-8

0.11

15

1,2-Dibromoethane/Ethylene dibromide

106-93-4

0.028

15

Dibromomethane

74-95-3

0.11

15

m-Dichlorobenzene

541-73-1

0.036

6.0

o-Dichlorobenzene

95-50-1

0.088

6.0

p-Dichlorobenzene

106-46-7

0.09

6.0

Dichlorodifluoromethane

75-71-8

0.23

7.2

1,1-Dichloroethane

75-34-3

0.059

6.0

1,2-Dichloroethane

107-06-2

0.21

6.0

1,1-Dichloroethylene

75-35-4

0.025

6.0

trans-1,2-Dichloroethylene

156-60-5

0.054

30

2,4-Dichlorophenol

120-83-2

0.044

14

2,6-Dichlorophenol

87-65-0

0.044

14

2,4-Dichlorophenoxyacetic acid/2,4-D

94-75-7

0.72

10

1,2-Dichloropropane

78-87-5

0.85

18

cis-1,3-Dichloropropylene

10061-01-5

0.036

18

trans-1,3-Dichloropropylene

10061-02-6

0.036

18

Dieldrin

60-57-1

0.017

0.13

Diethyl phthalate

84-66-2

0.20

28

p-Dimethylaminoazobenzene

60-11-7

0.13

NA

2,4-Dimethylphenol

105-67-9

0.036

14

Dimethyl phthalate

131-11-3

0.047

28

Di-n-butyl phthalate

84-74-2

0.057

28

1,4-Dinitrobenzene

100-25-4

0.32

2.3

4,6-Dinitro-o-cresol

534-52-1

0.28

160

2,4-Dinitrophenol

51-28-5

0.12

160

2,4-Dinitrotoluene

121-14-2

0.32

140

2,6-Dinitrotoluene

606-20-2

0.55

28

Di-n-octyl phthalate

117-84-0

0.017

28

Di-n-propylnitrosamine

621-64-7

0.40

14

1,4-Dioxane

123-91-1

12.0

170

Diphenylamine (difficult to distinguish from diphenylnitrosamine)

122-39-4

0.92

13

Diphenylnitrosamine (difficult to distinguish from diphenylamine)

86-30-6

0.92

13

1,2-Diphenylhydrazine

122-66-7

0.087

NA

Disulfoton

298-04-4

0.017

6.2

Dithiocarbamates (total)

NA

0.028

28

Endosulfan I

959-98-8

0.023

0.066

Endosulfan II

33213-65-9

0.029

0.13

Endosulfan sulfate

1031-07-8

0.029

0.13

Endrin

72-20-8

0.0028

0.13

Endrin aldehyde

7421-93-4

0.025

0.13

EPTC

759-94-4

0.042

1.4

Ethyl acetate

141-78-6

0.34

33

Ethyl benzene

100-41-4

0.057

10

Ethyl cyanide/Propanenitrile

107-12-0

0.24

360

Ethyl ether

60-29-7

0.12

160

Ethyl methacrylate

97-63-2

0.14

160

Ethylene oxide

75-21-8

0.12

NA

Famphur

52-85-7

0.017

15

Fluoranthene

206-44-0

0.068

3.4

Fluorene

86-73-7

0.059

3.4

Formetanate hydrochloride

23422-53-9

0.056

1.4

Heptachlor

76-44-8

0.0012

0.066

1,2,3,4,6,7,8-Heptachlorodibenzo-p-dioxin, (1,2,3,4,6,7,8-HpCDD)

35822-46-9

0.000035

0.0025

1,2,3,4,6,7,8-Heptachlorodibenzofuran, (1,2,3,4,6,7,8-HpCDF)

67562-39-4

0.000035

0.0025

1,2,3,4,7,8,9-Heptachlorodibenzofuran, (1,2,3,4,7,8,9-HpCDF)

55673-89-7

0.000035

0.0025

Heptachlor epoxide

1024-57-3

0.016

0.066

Hexachlorobenzene

118-74-1

0.055

10

Hexachlorobutadiene

87-68-3

0.055

5.6

Hexachlorocyclopentadiene

77-47-4

0.057

2.4

HxCDDs (All Hexachlorodibenzo-p-dioxins)

NA

0.000063

0.001

HxCDFs (All Hexachlorodibenzofurans)

NA

0.000063

0.001

Hexachloroethane

67-72-1

0.055

30

Indeno(1,2,3-cd)pyrene

193-39-5

0.0055

3.4

Iodomethane

74-88-4

0.19

65

Isobutyl alcohol

78-83-1

5.6

170

Isodrin

465-73-6

0.021

0.066

Isosafrole

120-58-1

0.081

2.6

Kepone

143-50-0

0.0011

0.13

Methacrylonitrile

126-98-7

0.24

84

Methanol

67-56-1

5.6

0.75 mg/L TCLP

Methapyrilene

91-80-5

0.081

1.5

Methiocarb

2032-65-7

0.056

1.4

Methomyl

16752-77-5

0.028

0.14

Methoxychlor

72-43-5

0.25

0.18

3-Methylcholanthrene

56-49-5

0.0055

15

4,4'-Methylene bis(2-chloroaniline)

101-14-4

0.50

30

Methylene chloride

75-09-2

0.089

30

Methyl ethyl ketone

78-93-3

0.28

36

Methyl isobutyl ketone

108-10-1

0.14

33

Methyl methacrylate

80-62-6

0.14

160

Methyl methanesulfonate

66-27-3

0.018

NA

Methyl parathion

298-00-0

0.014

4.6

Metolcarb

1129-41-5

0.056

1.4

Mexacarbate

315-18-4

0.056

1.4

Molinate

2212-67-1

0.042

1.4

Naphthalene

91-20-3

0.059

5.6

2-Naphthylamine

91-59-8

0.52

NA

o-Nitroaniline

88-74-4

0.27

14

p-Nitroaniline

100-01-6

0.028

28

Nitrobenzene

98-95-3

0.068

14

5-Nitro-o-toluidine

99-55-8

0.32

28

o-Nitrophenol

88-75-5

0.028

13

p-Nitrophenol

100-02-7

0.12

29

N-Nitrosodiethylamine

55-18-5

0.40

28

N-Nitrosodimethylamine

62-75-9

0.40

2.3

N-Nitroso-di-n-butylamine

924-16-3

0.40

17

N-Nitrosomethylethylamine

10595-95-6

0.40

2.3

N-Nitrosomorpholine

59-89-2

0.40

2.3

N-Nitrosopiperidine

100-75-4

0.013

35

N-Nitrosopyrrolidine

930-55-2

0.013

35

1,2,3,4,6,7,8,9-Octachlorodibenzo-p-dioxin, (OCDD)

3268-87-9

0.000063

0.005

1,2,3,4,6,7,8,9-Octachlorodibenzofuran, (OCDF)

39001-02-0

0.000063

0.005

Oxamyl

23135-22-0

0.056

0.28

Parathion

56-38-2

0.014

4.6

Total PCBs (sum of all PCB isomers, or all Aroclors)

1336-36-3

0.10

10

Pebulate

1114-71-2

0.042

1.4

Pentachlorobenzene

608-93-5

0.055

10

PeCDDs (All Pentachlorodibenzo-p-dioxins)

NA

0.000063

0.001

PeCDFs (All Pentachlorodibenzofurans)

NA

0.000035

0.001

Pentachloroethane

76-01-7

0.055

6.0

Pentachloronitrobenzene

82-68-8

0.055

4.8

Pentachlorophenol

87-86-5

0.089

7.4

Phenacetin

62-44-2

0.081

16

Phenanthrene

85-01-8

0.059

5.6

Phenol

108-95-2

0.039

6.2

Phorate

298-02-2

0.021

4.6

Phthalic acid

100-21-0

0.055

28

Phthalic anhydride

85-44-9

0.055

28

Physostigmine

57-47-6

0.056

1.4

Physostigmine salicylate

57-64-7

0.056

1.4

Promecarb

2631-37-0

0.056

1.4

Pronamide

23950-58-5

0.093

1.5

Propham

122-42-9

0.056

1.4

Propoxur

114-26-1

0.056

1.4

Prosulfocarb

52888-80-9

0.042

1.4

Pyrene

129-00-0

0.067

8.2

Pyridine

110-86-1

0.014

16

Safrole

94-59-7

0.081

22

Silvex/2,4,5-TP

93-72-1

0.72

7.9

1,2,4,5-Tetrachlorobenzene

95-94-3

0.055

14

TCDDs (All Tetrachlorodibenzo-p-dioxins)

NA

0.000063

0.001

TCDFs (All Tetrachlorodibenzofurans)

NA

0.000063

0.001

1,1,1,2-Tetrachloroethane

630-20-6

0.057

6.0

1,1,2,2-Tetrachloroethane

79-34-5

0.057

6.0

Tetrachloroethylene

127-18-4

0.056

6.0

2,3,4,6-Tetrachlorophenol

58-90-2

0.030

7.4

Thiodicarb

59669-26-0

0.019

1.4

Thiophanate-methyl

23564-05-8

0.056

1.4

Toluene

108-88-3

0.080

10

Toxaphene

8001-35-2

0.0095

2.6

Triallate

2303-17-5

0.042

1.4

Tribromomethane/Bromoform

75-25-2

0.63

15

1,2,4-Trichlorobenzene

120-82-1

0.055

19

1,1,1-Trichloroethane

71-55-6

0.054

6.0

1,1,2-Trichloroethane

79-00-5

0.054

6.0

Trichloroethylene

79-01-6

0.054

6.0

Trichlorofluoromethane

75-69-4

0.020

30

2,4,5-Trichlorophenol

95-95-4

0.18

7.4

2,4,6-Trichlorophenol

88-06-2

0.035

7.4

2,4,5-Trichlorophenoxyacetic acid/ 2,4,5-T

93-76-5

0.72

7.9

1,2,3-Trichloropropane

96-18-4

0.85

30

1,1,2-Trichloro-1,2,2-trifluoroethane

76-13-1

0.057

30

Triethylamine

121-44-8

0.081

1.5

Tris(2,3-Dibromopropyl) phosphate

126-72-7

0.11

0.1

Vernolate

1929-77-7

0.042

1.4

Vinyl chloride

75-01-4

0.27

6.0

Xylenes-mixed isomers (sum of o-, m-, and p-xylene concentrations)

1330-20-7

0.32

30

Notes to Table 1:

1. CAS Number means the Chemical Abstracts Service Registry Number. When the waste or a regulated constituent is described as a combination of a chemical with its salts or esters, the CAS number is given for the parent compound only.

2. Concentration requirements for aqueous wastes are expressed in mg/L and are based on analysis of composite samples.

3. Concentration requirements for non-aqueous wastes are based on analysis of grab samples.

Table 2
Inorganic Constituents

 

Column 1

Regulated Constituent:

Common Name

Column 2

Regulated Constituent:

CAS Number

Column 3

Land Disposal Treatment Requirements for Aqueous Waste:

Concentration (mg/L)

Column 4

Land Disposal Treatment Requirements for Non-aqueous Waste:

Concentration (mg/kg, unless otherwise indicated)

Antimony

7440-36-0

1.9

1.15 mg/L TCLP

Arsenic

7440-38-2

1.4

5.0 mg/L TCLP

Barium

7440-39-3

1.2

21 mg/L TCLP

Beryllium

7440-41-7

0.82

1.22 mg/L TCLP

Cadmium

7440-43-9

0.69

0.11 mg/L TCLP

Chromium (Total)

7440-47-3

2.77

0.60 mg/L TCLP

Cyanides (Total)

57-12-5

1.2

590

Cyanides (Amenable)

57-12-5

0.86

30

Lead

7439-92-1

0.69

0.75 mg/L TCLP

Mercury-Non-aqueous waste from Retort

7439-97-6

NA

0.20 mg/L TCLP

Mercury-All Others

7439-97-6

0.15

0.025 mg/L TCLP

Nickel

7440-02-0

3.98

11 mg/L TCLP

Silver

7440-22-4

0.43

0.14 mg/L TCLP

Thallium

7440-28-0

1.4

0.20 mg/L TCLP

Notes to Table 2:

1. CAS Number means the Chemical Abstracts Service Registry Number. When the waste or a regulated constituent is described as a combination of a chemical with its salts or esters, the CAS number is given for the parent compound only.

2. Concentration requirements for aqueous wastes are expressed in mg/L and are based on analysis of composite samples.

3. Concentration requirements for non-aqueous wastes are based on analysis of grab samples.

4. Both Cyanides (Total) and Cyanides (Amenable) for non-aqueous wastes are to be analyzed using Method 9010 or 9012, found in “Test Methods for Evaluating Solid Waste, Physical/ Chemical Methods”, United States Environmental Protection Agency Publication SW–846, with a sample size of 10 grams and a distillation time of one hour and 15 minutes.

10. Schedule 8 to the Regulation is revoked and the following substituted:

Schedule 8
Alternative Treatment for Hazardous Debris

A reference to this Schedule in this Regulation is a reference to the relevant Table of this Schedule, including the Notes to the Table.

Table 1
Extraction Technologies

 

Treatment Method

Standard

Debris and Contaminant Restrictions

Physical Extraction - Abrasive Blasting:

Removal of contaminated debris surface layers using water or air pressure to propel a solid abrasive (e.g., steel shot, aluminum oxide grit, plastic beads).

For Glass, Metal, Plastic, Rubber: Treatment to a clean debris surface.
For Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: Removal of at least 0.6 cm of the surface layer; treatment to a clean debris surface.

No Restrictions

Physical Extraction - Scarification, Grinding, and Planing:

Process utilizing striking piston heads, saws, or rotating grinding wheels such that contaminated debris surface layers are removed.

For Glass, Metal, Plastic, Rubber: Treatment to a clean debris surface.
For Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: Removal of at least 0.6 cm of the surface layer; treatment to a clean debris surface.

No Restrictions

Physical Extraction - Spalling:

Drilling or chipping holes at appropriate locations and depth in the contaminated debris surface and applying a tool which exerts a force on the sides of those holes such that the surface layer is removed.  The surface layer removed remains subject to the debris treatment standards.

For Glass, Metal, Plastic, Rubber: Treatment to a clean debris surface.
For Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: Removal of at least 0.6 cm of the surface layer; treatment to a clean debris surface.

No Restrictions

Physical Extraction - Vibratory Finishing:

Process utilizing scrubbing media, flushing fluid, and oscillating energy such that hazardous contaminants or contaminated debris surface layers are removed.

For Glass, Metal, Plastic, Rubber: Treatment to a clean debris surface.
For Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: Removal of at least 0.6 cm of the surface layer; treatment to a clean debris surface.

No Restrictions

Physical Extraction - High Pressure Steam and Water Sprays:

Application of water or steam sprays of sufficient temperature, pressure, residence time, agitation, surfactants, and detergents to remove hazardous contaminants from debris surfaces or to remove contaminated debris surface layers.

For Glass, Metal, Plastic, Rubber: Treatment to a clean debris surface.
For Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: Removal of at least 0.6 cm of the surface layer; treatment to a clean debris surface.

No Restrictions

Chemical Extraction - Water Washing and Spraying:

Application of water sprays or water baths of sufficient temperature, pressure, residence time, agitation, surfactants, acids, bases, and detergents to remove hazardous contaminants from debris surfaces and surface pores or to remove contaminated debris surface layers.

For all Debris: Treatment to a clean debris surface;
For Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: Debris must be no more than 1.2 cm (½ inch) in one dimension (i.e., thickness limit); debris surfaces must be in contact with water solution for at least 15 minutes;

For debris contaminated with a dioxin-characteristic waste, treatment must be carried out in accordance with an environmental compliance approval, despite any exemptions that might otherwise apply.

For Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: Restricted unless the contaminant is soluble to at least 5% by weight in water solution or 5% by weight in emulsion.

Chemical Extraction - Liquid Phase Solvent Extraction:

Removal of hazardous contaminants from debris surfaces and surface pores by applying a non-aqueous liquid or liquid solution which causes the hazardous contaminants to enter the liquid phase and be flushed away from the debris along with the liquid or liquid solution while using appropriate agitation, temperature, and residence time.

For all Debris: Treatment to a clean debris surface;
For Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: Debris must be no more than 1.2 cm (½ inch) in one dimension (i.e., thickness limit) ; debris surfaces must be in contact with water solution for at least 15 minutes;

For debris contaminated with a dioxin-characteristic waste, treatment must be carried out in accordance with an environmental compliance approval, despite any exemptions that might otherwise apply.

For Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: Restricted unless the contaminant is soluble to at least 5% by weight in the solvent.

Chemical Extraction - Vapour Phase Solvent Extraction:

Application of an organic vapour using sufficient agitation, residence time, and temperature to cause hazardous contaminants on contaminated debris surfaces and surface pores to enter the vapour phase and be flushed away with the organic vapour.

For all Debris: Treatment to a clean debris surface;
For Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: Debris must be no more than 1.2 cm (½ inch) in one dimension (i.e., thickness limit) ; debris surfaces must be in contact with the organic vapour for at least 60 minutes;

For debris contaminated with a dioxin-characteristic waste, treatment must be carried out in accordance with an environmental compliance approval, despite any exemptions that might otherwise apply.

For Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: Restricted unless the contaminant is soluble to at least 5% by weight in the solvent.

Thermal Extraction - High Temperature Metals Recovery:

Application of sufficient heat, residence time, mixing, fluxing agents, or carbon in a smelting, melting, or refining furnace to separate metals from debris.

Separate metal from treated debris;

For debris contaminated with a dioxin-characteristic waste, treatment must be carried out in accordance with an environmental compliance approval, despite any exemptions that might otherwise apply.

No Restrictions

Thermal Extraction - Thermal Desorption:

Heating in an enclosed chamber under either oxidizing or nonoxidizing atmospheres at sufficient temperature and residence time to vaporize hazardous contaminants from contaminated surfaces and surface pores and to remove the contaminants from the heating chamber in a gaseous exhaust gas.

For all Debris: Vaporize hazardous contaminants from contaminated surfaces and surface pores and remove the contaminants from the heating chamber in a gaseous exhaust gas.  This must be done in accordance with an environmental compliance approval, despite any exemptions that might otherwise apply.
For Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: Debris must be no more than 10 cm (4 inches) in one dimension (i.e., thickness limit).

For all Debris: Restricted for metal contaminants other than mercury.

Notes to Table 1:

1. Where a contaminant restriction is set out for a treatment method and type of debris, the use of that treatment method is not sufficient if that type of debris contains the restricted contaminant. If the restricted treatment is used, the debris must also be treated by another treatment method that is described in the Schedule and for which no restriction is set out for that type of debris and contaminant.

2. “Clean debris surface” means that the surface, when viewed without magnification, must be free of all visible contaminated soil and hazardous waste, except that residual staining from soil and waste that consists of light shadows, slight streaks or minor discolorations may be present, and soil and waste in cracks, crevices or pits may be present, if the residual staining or the waste and soil in cracks, crevices or pits is limited to not more than 5% of each square inch of surface area.

3. Thickness Limit for Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: If reducing the particle size of debris to meet the treatment standards results in material that no longer meets the 60 mm minimum particle size limit for debris, the material is subject to the waste-specific treatment standards for the waste contaminating the material, unless the debris has been cleaned and separated from contaminated soil and waste prior to size reduction. Alternative thickness limits may be used by obtaining an environmental compliance approval.

Table 2
Destruction Technologies

 

Treatment Method

Standard

Restrictions

Biological Destruction (Biodegradation):

Removal of hazardous contaminants from debris surfaces and surface pores in an aqueous solution and biodegradation of organic or nonmetallic inorganic compounds (i.e., inorganics that contain phosphorus, nitrogen, or sulphur) in units operated under either aerobic or anaerobic conditions.

For all Debris: Removal of hazardous contaminants and biodegradation of organic or nonmetallic inorganic compounds.  This must be done in accordance with an environmental compliance approval, despite any exemptions that might otherwise apply.
For Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: Debris must be no more than 1.2 cm (1\2 inch) in one dimension (i.e., thickness limit).

For all Debris: Restricted for metal contaminants.

Chemical Destruction: Chemical Oxidation:

Chemical or electrolytic oxidation utilizing the following oxidation reagents (or waste reagents) or combination of reagents:
- hypochlorite (e.g., bleach);
- chlorine;
- chlorine dioxide;
- ozone or UV (ultraviolet light) assisted ozone;
- peroxides;
- persulphates;
- perchlorates;
- permanganates;
- other oxidizing reagents of equivalent destruction efficiency.
Chemical oxidation specifically includes what is referred to as alkaline chlorination.

For all Debris: Chemical or electrolytic oxidation.  This must be done in accordance with an environmental compliance approval, despite any exemptions that might otherwise apply.
For Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: Debris must be no more than 1.2 cm (1\2 inch) in one dimension (i.e., thickness limit).

For all Debris: Restricted for metal contaminants.

Chemical Destruction: Chemical Reduction:

Chemical reaction utilizing the following reducing reagents (or waste reagents) or combination of reagents:
- sulphur dioxide;
- sodium, potassium, or alkali salts of sulphites, bisulphites, and metabisulphites, and polyethylene glycols (e.g., NaPEG and KPEG);
- sodium hydrosulphide;
- ferrous salts;
- other reducing reagents of equivalent efficiency.

For all Debris: Chemical Reduction.  This must be done in accordance with an environmental compliance approval, despite any exemptions that might otherwise apply.
For Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: Debris must be no more than 1.2 cm (1\2 inch) in one dimension (i.e., thickness limit).

For all Debris: Restricted for metal contaminants.

Thermal Destruction:

Thermal treatment, excluding Thermal Desorption units.

For all Debris: Thermal destruction or vitrification.  This must be done in accordance with an environmental compliance approval, despite any exemptions that might otherwise apply.

For Brick, Concrete, Glass, Metal, Pavement, Rock:  Restricted for metal contaminants other than mercury, except that there are no metal restrictions for vitrification.

Notes to Table 2:

1. Where a contaminant restriction is set out for a treatment method and type of debris, the use of that treatment method is not sufficient if that type of debris contains the restricted contaminant. If the restricted treatment is used, the debris must also be treated by another treatment method that is described in the Schedule and for which no restriction is set out for that type of debris and contaminant.

2. Thickness Limit for Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: If reducing the particle size of debris to meet the treatment standards results in material that no longer meets the 60 mm minimum particle size limit for debris, the material is subject to the waste-specific treatment standards for the waste contaminating the material, unless the debris has been cleaned and separated from contaminated soil and waste prior to size reduction. Alternative thickness limits may be used by obtaining an environmental compliance approval.

Table 3
Immobilization Technologies

 

Treatment Method

Standard

Restriction

Macroencapsulation:

Application of surface coating materials such as polymeric organics (e.g., resins and plastics) or use of a jacket of inert inorganic materials to substantially reduce surface exposure to potential leaching media.

Encapsulating material must completely encapsulate debris and be resistant to degradation by the debris and its contaminants and materials into which it may come into contact after placement (leachate, other waste, microbes), and substantially reduce surface exposure to potential leaching media.

No Restrictions

Microencapsulation:

Stabilization of the debris with the following reagents (or waste reagents) such that the leachability of the contaminants is reduced:
- Portland cement;
- lime/pozzolans (e.g., fly ash and cement kiln dust).
Reagents (e.g., iron salts, silicates, and clays) may be added to enhance the set/cure time or compressive strength, or to reduce the leachability of the contaminants.

Leachability of the contaminants must be reduced.

No Restrictions

Sealing:

Application of an appropriate material which adheres tightly to the debris surface to avoid exposure of the surface to potential leaching media.  When necessary to effectively seal the surface, sealing entails pretreatment of the debris surface to remove foreign matter and to clean and roughen the surface.  Sealing materials include epoxy, silicone, and urethane compounds, but paint may not be used as a sealant.

Sealing must avoid exposure of the debris surface to potential leaching media and sealant must be resistent to degradation by the debris and its contaminants and materials into which it may come into contact after placement (leachate, other waste, microbes).

No Restrictions

Note to Table 3:

1. Note re: microencapsulation: If reducing the particle size of debris to meet the treatment standards results in material that no longer meets the 60 mm minimum particle size limit for debris, the material is subject to the waste-specific treatment standards for the waste contaminating the material, unless the debris has been cleaned and separated from contaminated soil and waste prior to size reduction. Alternative thickness limits may be used by obtaining an environmental compliance approval.

11. Schedules 10 to 13 to the Regulation are revoked.

Commencement

12. This Regulation comes into force on the day it is filed.